Name: Forum Synthetic Engine Oil Additive 250ml for 4-stroke engines FR001
Brand: ECRATER
SKU: BMZVV33J1X
Price: 60 USD
Availability: InStock

Forum Synthetic Engine Oil Additive 250ml for 4-stroke engines FR001
FORUM SYNTHETIC is a premium product designed for maximum protection, life saving and restoration of friction surfaces of all types of 4-stroke engines. Compatible with all types of oils.
All Forum&reg; additives are based on ultra-dispersed polytetrafluoroethylene-Forum (UPTFE-Forum&reg;) powder, which consists of various temperature fractions. All additives contain a mixture of these fractions, and only FORUM SYNTHETIC contains exclusively high-temperature fractions. Since the high-temperature fraction is obtained under the most severe conditions, its layers are the most wear-resistant. In addition, this product is manufactured using group IV synthetic oil. All these features provide a higher efficiency of the additive.
FORUM SYNTHETIC is used for turbocharged engines. The presence of turbines increases the effectiveness of the additive, since the UPTFE-Forum&reg; coating withstands high temperatures (400 &deg; C and up to 500 &deg; C for a short time) and is very firmly held on the friction surface, which dramatically reduces wear and the likelihood of turbine breakage, especially during start-up and when there is a lack of oil .
Effects of using FORUM SYNTHETIC:
Provides maximum protection of working surfaces against friction and wear, especially at high temperature and mechanical loads. Reduces the coefficient of friction in oil by 20%, in the absence of oil by 100 times. Increases engine power up to 30%. Reduces surface wear by 5&ndash;15 times. Reduces noise and vibration levels by 2-8 dB. Saves fuel up to 20%. Quickly restores damaged surfaces. Extends oil life by 2-3 times. Increases compression in the cylinders. Eliminates wear during "cold start". Composition: UPTFE-Forum&reg; high-temperature fraction, Group 4 synthetic base oil.
FORUM SYNTHETIC is used when changing the oil in an engine with a clean oil filter according to the following scheme:
Drain the old engine oil and replace the oil filter. Shake the vial vigorously until the active component of UPTFE-Forum&reg; is distributed throughout the entire volume of the liquid. Pour the additive into a container with new engine oil and mix. The presence of a small amount of sediment at the bottom of an empty vial after its use is allowed. Pour oil with the additive into the engine and let it run for at least 15 minutes in order to evenly distribute the additive throughout the system. FORUM SYNTHETIC is recommended to be used with every oil change. One bottle is designed for 3-7 liters of oil.
If, when changing the oil and changing the filter, it was not possible to add FORUM SYNTHETIC at the same time, then this can be done before the car runs 500 km. In this case, the additive must be poured through the engine oil filler neck for 5 minutes into a running engine or 2&ndash;3 portions into a turned off engine, each time after adding the next portion, start the engine for 5 minutes.
The effect of the use of the additive manifests itself no later than after 200&ndash;500 km of run, increases and persists throughout the entire service life of the oil.
<img src="https://cdn.inspireuplift.com/uploads/images/seller_products/1667289883_Auto-doctor-autodoctorrussia-inspireuplift-ebay.jpg" alt="Auto-doctor-autodoctorrussia-inspireuplift-ebay.jpg" width="1236" height="532" />

ECRATER

<ul>
<li>The order processing time is 1-7 working days.</li>
<li>The delivery time depends on your country or region. The average delivery time is 2-4 weeks.</li>
<li>Can be increased in the pre-holiday season.</li>
<li>For questions and requests please email admin@ecrater.ru</li>
</ul>

Forum Synthetic Engine Oil Additive 250ml for 4-stroke engines FR001

Quantity

Similar Products